Have you been on the lookout for advise about How to Install a Bathtub?
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bath tub with a new one is also a reasonably hard project. If the old tub is easily obtainable, the task can move quickly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually qualified yourself for the job and are comfortable attempting it. Instead of working with a service provider to take control of a halfway-completed project, it is better to consider utilizing one before you begin. Possibilities are you might require an expert plumber to make tube links.
This post will certainly aid you mount a brand-new bath tub in your shower room if you have actually currently gotten a brand-new bathtub as well as do not require to alter the plan of your previous water system pipes.
Your tools as well as material checklist need to consist of the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have been removed, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Prior to moving on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in area in between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bathtub up until the level reads level.
To mount taps, fit the bottom of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leaks.
Finally, take care of the bathroom paneling as described in the supplier's instruction manual. Tiling and sealing around the tub ought to wait up until the tub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.
Getting ready for the Setup
First of all, the sustaining framework provided with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps system to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to crack an inflexible seal, triggering the water to permeate the wall in between the bath and the tiling, leading to difficulties with moisture and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as can securing voids up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on How to Install a Bathtub, I assumed sharing that article was worth the trouble. I beg you take the opportunity to distribute this blog post if you enjoyed it. We love reading our article about Installing A Bathtub.
Schedule Service Pickup